pb lead-free parts surface mount tape and reel ligitek electronics co.,ltd. property of ligitek only data sheet doc. no : qw0905-LUR9S53 rev. : a date : 25 - dec. - 2006 LUR9S53
ligitek electronics co.,ltd. property of ligitek only 1.3 0.7 1.3 1.4 2.0 page 1/6 0.7 part no. LUR9S53 package dimensions 3.0 2.7 - 30 60 0 100% 50%75% 0 25%25% + -60 75% 100% note : 1.all dimension are in millimeter tolerance is 0.25mm unless otherwise noted. 2.specifications are subject to change without notice. directivity radiation 50% -30
unit mw ma ma pd i fp i f 120 120 40 ratings ur parameter power dissipation forward current peak forward current duty 1/10@10khz absolute maximum ratings at ta=25 symbol a ir tstg t opr -40 ~ +100 -40 ~ +85 10 storage temperature operating temperature reverse current @5v typical electrical & optical characteristics (ta=25 ) ligitek electronics co.,ltd. property of ligitek only page 2/6 luminous intensity @20ma(mcd) 130 140 80 2.4 max. min. typ. spectral halfwidth nm peak wave length pnm 20 660 forward voltage @20ma(v) min. 1.5 material red gaalas emitted LUR9S53 part no water clear note : 1.the forward voltage data did not including 0.1v testing tolerance. 2. the luminous intensity data did not including 15% testing tolerance. lens color viewing angle 2 1/2 (deg) part no. LUR9S53
ligitek electronics co.,ltd. property of ligitek only 0.0 0.8 f o r w a r d v o l t a g e @ 2 0 m a n o r m a l i z e @ 2 5 r e l a t i v e i n t e n s i t y @ 2 0 m a n o r m a l i z e @ 2 5 wavelength (nm) ambient temperature( ) fig.5 relative intensity vs. wavelength r e l a t i v e i n t e n s i t y @ 2 0 m a 1.0 0.0 600 0.5 -40-20 650700750 -40 80 20 04060100 ambient temperature( ) -20040 20100 80 60 1 f o r w a r d c u r r e n t ( m a ) r e l a t i v e i n t e n s i t y n o r m a l i z e @ 2 0 m a fig.3 forward voltage vs. temperature 0.9 1.0 1.1 1.2 0 1 1.0 1.0 0.5 1.5 2.0 2.5 3.0 1 fig.4 relative intensity vs. temperature forward voltage(v) 3.0 2.04.0 0.0 5.0 0.5 forward current(ma) 100 101000 fig.1 forward current vs. forward voltage typical electro-optical characteristics curve 10 100 1000 ur chip fig.2 relative intensity vs. forward current 2.5 1.5 1.0 2.0 3.0 page 3/6 part no. LUR9S53
ligitek electronics co.,ltd. property of ligitek only soldering heat max. 260 1. hand solder basic spec is Q 280 3 sec one time only. 2. wave solder recommended soldering conditions 120 ~ 150 preheat 120 ~ 180 sec 245 5 within 5 sec page 4/6 240 temp. ( ) preheat 120 150 cooling -5 /sec rising +5 /sec 1~5 c/sec 60 ~ 120 sec 5sec 4. pb-free reflow solder 260 c max. 10sec.max time preheat 180~200 c above 220 c 60 sec.max. 1~5 c/sec 120 sec.max. note:1.wave solder and reflow soldering should not be made more than one time. 2.you can just only select one of the soldering conditions as above. 3. lead reflow solder part no. LUR9S53
page 5/6 precautions for use: storage time: 1.the operation of temperatures and rh are : 5 ~35 ,rh<60%. 2.once the package is opened, the products should be used within a week. otherwise, they should be kept in a damp proof box with descanting agent. considering the tape life, we suggest our customers to use our products within a year(from production date). 3.if opened more than one week in an atmosphere 5 ~ 35 ,rh<60%, they should be treated at 60 5 fo r 15hrs. ligitek electronics co.,ltd. property of ligitek only led led circuit model a cleaning: use alcohol-based cleaning solvents such as isopropyl alcohol to clean the led. (a) recommended circuit. (b) the difference of brightness between led could be found due to the vf-if characteristics of led. esd(electrostatic discharge): static electricity or power surge will damage the led. use of a conductive wrist band or anti-electrosatic glove is recommended when handing these led. all devices, equipment and machinery must be properly grounded. circuit model b drive method: led is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. this current limiting typically takes the form of a current limiting resistor placed in series with the led. consider worst case voltage variations than could occur across the current limiting resistor. the forwrd current should not be allowed to change by more than 40% of its desired value. part no. LUR9S53
ligitek electronics co.,ltd. property of ligitek only reference standard mil-std-883d:1008 jis c 7021: b-10 jis c 7021: b-12 mil-std-750d: 1026 mil-std-883d: 1005 jis c 7021: b-1 test condition test item operating life test classification reliability test: high temperature storage test 1.ta=105 5 2.t=1000 hrs (-24hrs, +72hrs) low temperature storage test 1.ta=-40 5 2.t=1000 hrs (-24hrs, +72hrs) endurance test 1.ta=under room temperature as per data sheet maximum rating. 2.if=20ma 3.t=1000 hrs (-24hrs, +72hrs) page 6/6 mil-std-202f: 208d mil-std-750d: 2026 mil-std-883d: 2003 iec 68 part 2-20 jis c 7021: a-2 mil-std-202f: 107d mil-std-750d: 1051 mil-std-883d: 1011 mil-std-202f: 107d mil-std-750d: 1051 mil-std-883d: 1010 jis c 7021: a-4 mil-std-750d:2031.2 j-std-020 thermal shock test solderability test 1.t.sol=235 5 2.immersion time 2 0.5sec 3.immersion rate 25 2.5mm/sec 4.immersion rate 25 2.5mm/sec 5.coverage R 95% of the dipped surface 1.ir-reflow in-board,2 times 2.ta=105 5 & -40 5 (10min) (10min) 3.total 10 cycles temperature cycling 1.105 ~ 25 ~ 55 ~ 25 30mins 5mins 30mins 5mins 2.10 cyeles solderability test environmental test ramp-up rate(183 to peak) +3 second max temp. maintain at 125( 25) 120 seconds max temp. maintain above 183 60-150 seconds peak temperature range 235 +5-0 time within 5 of actual peak temperature(tp) 10-30 seconds ramp-down rate +6 /second max high temperature high humidity storage test 1.ir-reflow in-board, 2 times 2.ta=65 5 3.rh=90%~95% 4.t=1000hrs 2hrs mil-std-202f:103b jis c 7021: b-11 part no. LUR9S53
|
